CA AE08, Candy Apple Red Acrylic Enamel Paint

Description

CS AE08, Candy Apple Red Acrylic Enamel Paint
Paint - 1 U.S. Gallon
Wet Look Hardener - 16 Fl. Oz
Activator/Hardener is not required but may be added for optimum gloss holdout and extended durability.
Depending on temperature and gun setup Acrylic Enamel Reducer may be needed for flow.
Classic Series factory-packaged AE Acrylic Enamel Paint is an easy to use Automotive Single Stage Topcoat paint finish that produces a durable, High Gloss shine, and long lasting protection. Classic Series is designed to be used as a complete automotive, commercial, fleet, or agricultural paint system.
Classic Series Acrylic Enamel factory-packaged paint is available in 20 popular pre-mixed colors. This easy-to-use single-stage topcoat provides excellent durability for a variety of applications including cars, trucks and commercial equipment.
AE01
Super Jet Black
AE02
Pure White
AE03
Fleet White (GM Code 12)
AE04
Mack White
AE05
Silver Metallic
AE06
Platinum Silver Metallic
AE07
Gray Metallic
AE08
Candy Apple Red
AE09
Mack Red
AE10
Viper Red
AE11
Mack Green
AE12
School Bus Yellow
AE13
Viper Yellow
AE14
Dark Jade Green Metallic
AE15
Mack Blue
AE16
Blue Metallic
AE17
Ultra Blue Pearl
AE18
Royal Blue Pearl
AE19
Black Cherry Pearl
AE20
Black Starburst Pearl
PREP STEPS:
Prep surfaces by removing all traces of wax, grease, silicone, oil and other contaminants with a detergent wash, followed with a solvent-based cleaner. Abrade surface with 600-800 grit sandpaper to ensure proper adhesion. Re-clean with a final prep cleaner. Tack entire surface.
MIXING DIRECTIONS:
Thoroughly shake, then stir Classic Series Acrylic Enamel. To ensure color consistency when working with multiple gallons, it is always recommended to blend the contents of all gallons together prior to mixing.
Mix with Acrylic Enamel Reducer 4:1 by volume (4 parts paint, 1 part reducer). Depending on temperature, air flow and other conditions, additional reduction may be required. Always be sure to choose the correct speed Acrylic Enamel Reducer for the conditions at the time of application. Using the correct speed will reduce the risk of application errors including runs, orange peel, die back, wrinkling, solvent pop and more.
For improved durability, increased gloss and faster dry times, add one pint Classic Series Wet Look Hardener for every gallon of paint. When using optional Acrylic Enamel Hardener, mix ratio becomes 8:2:1 (8 parts paint, 2 parts reducer, 1 part hardener).
POT LIFE:
Pot life of paint once mixed with hardener is approximately 2-3 hours at 70°F.
APPLICATION:
Use an HVLP gun with a 1.2—1.4 mm tip and 8-10 psi at the cap. Refer to spray equipment manufacturer’s recommendations for further information.
Apply 2-3 medium wet coats as necessary to achieve the desired coverage,
allowing each coat to dry hand slick (approximately 20-30 minutes) before applying the next coat. A dry film thickness of 2 mils is recommended. BE sure to spray even, consistent coats with proper technique.
For metallic and pearl colors, consistent application technique is critical to prevent mottling and other inconsistencies in the finish. Uneven coats resulting in wet/dry areas will create the appearance of striping or spotting.
For colors with lower hiding ability, a consistent, solid-colored ground coat is recommended.
DRY TIMES:
Classis Series Acrylic Enamel will dry tack-free in one hour (two hours if applied without the optional hardener). Dry time may be more or less depending on temperature, air movement, film thickness and other factors.
May be force-dried for 30 minutes at 140°F after a 20-30 minute flash. Do not force dry if applied without optional hardener.
Wait at least 24 hours to tape or otherwise handle. If applied without optional hardener, wait at least a week before taping on the surface.
RECOATING:
May be recoated once previous coat dries hand slick, or up to three hours later. After three hours, Class Series Acrylic Enamel enters a sensitive recoat window, so be sure to wait at least 24 hours for paint to cure before abrading, then recoating. If applied without optional hardener, wait at least a week before recoating.
Acrylic Enamel may be clear coated for improved durability and
gloss following the same recommended recoat procedure outlined above.
POLISH:
Wait at least 24-48 hours before polishing Classic Series Acrylic Enamel paint, depending on temperature, air movement, film thickness and other factors.
If applied without optional hardener, wait at least a month before polishing.
To polish, sand with 1500 grit or finer to open the film and remove any imperfections in the finish. For metallic/pearl colors, lightly sand only. Aggressive sanding, even with 1500 grit, can disturb the effect particles near the surface of the film. Follow with 2000 grit then use a high quality finishing compound followed by a finishing glaze applied by hand or with a variable speed buffer.
CLEAN UP:
Close all containers tightly after each use. Clean gun and spray equipment with gun wash or other appropriate solvent product immediately after application to prevent damage.
HEALTH / SAFETY:
THIS PRODUCT IS INTENDED FOR USE BY PROFESSIONALS ONLY.
USE THIS PRODUCT ONLY WITH ADEQUATE VENTILATION: Wear appropriate, properly fitted fresh-air-supplied NIOSH/MSHA-approved respirator (TC-19C or equivalent) as directed by the manufacturer. Protect hands with impervious nitrile gloves. Always wear eye and face protection. Individuals with lung or breathing problems should neither use nor be exposed to this product, its vapors or spray mist. READ ALL WARNINGS ON ALL LABELS BEFORE USING.
This product is designed to be mixed with other components. Mixture will have hazards of all components. Before opening the packages, read all warning labels. Follow all precautions. See Material Safety Data Sheet for additional health andsafety information.
WARRANTY:
This product is manufactured from first-class material. Directions for use of this system are based on tests, information and experience believed to be reliable. Neither the manufacturer nor the seller has control over the methods and/or conditions of use or actual application of this product. It is the responsibility of the user to determine the suitability of this product for its intended use. Product warranty shall be limited to the replacement of defective materials only. No other warranty is expressed or implied. The buyer and all users are deemed to have accepted the terms of this notice, which may not be varied.
PHYSICALS:
PRODUCT:
Automotive topcoat (National Rule Compliant)
PACKAGE:
1 U.S. Gallon/128 fl. oz. (3.785 Liters)
MAX VOC ALLOWED:
Not to exceed 5.0 lbs/gallon (ready for use)
ACTUAL VOC (as supplied):
Varies by color
REGULATORY VOC (as supplied):
Varies by color